Ad | Jinan Water Chiller Inc.

Basic Info.

Model NO.	AD-1600
Capacity	1.0-26 M3/Min
Voltage	380V
Warranty	1 Year
Working Pressure	0.7~1.3MPa
Dryer Type	Refrigerated Dryer
Transport Package	Wooden Case
Specification	1050x660x1130mm
Trademark	Atlas Copco- Pneumatech
Origin	Wuxi
Production Capacity	200/Month

Product Description

Ad-1600 Oaliss Atlas Copco Bolaite Pneumatech Heated Purge Desiccant Air Dryer

How to remove the water?
There are several ways to remove water and moisture from compressed air.1. The first method is overcompression, the pressure is increased to a level above the required compressed air pressure and at this higher pressure the free water droplets are removed. In the next step, the pressure is decreased to the required compressed air pressure. From this stage, only water vapor is present in the compressed air, the relative humidity dropped below 100%.2. A second method is cooling, the compressed air is cooled down to a lower temperature. At this lower temperature, the relative humidity exceeds 100% and free water droplets are formed. Those free water droplets are collected and removed. In the next step the temperature of the compressed air is increased again. Fromthis stage, only water vapor is present in the compressed air, the relative humidity dropped below 100%.3. As third method chemical drying is often used, the moisture is removed by absorption or adsorption in a certain substance. With absorption, the moisture is captured in a hygroscopic liquid or powder. The moisture is attached to this material and needs to be removed and replaced by new material for further operation.With adsorption, the moisture is captured in hygroscopic beads. The moisture molecules are transported into the pores through diffusion and are accumulated through physical binding and capillary condensation. In this case, when the beads are saturated, they have to be regenerated before they can start adsorbing again. The regenerationcan be done by heating the beads or by sending extreme dry air over the beads. In both cases the water retaining forces are broken and the water molecules are removed.
Specification

Item	Description
Type	Refrigerated dryer
Warranty	1 Year
Applicable Industries	Hotels, Garment Shops, Building Material Shops, Manufacturing Plant, Machinery Repair Shops, Food & Beverage Factory, Farms, Restaurant, Home Use, Retail, Food Shop, Printing Shops, Construction works, Energy & Mining, Food & Beverage Shops, Other, Advertising Company
After Warranty Service	Spare parts
Local Service Location	Thailand, Vietnam, Pakistan, Russia, Sri Lanka
Showroom Location	Thailand, Vietnam, Pakistan, Russia, Sri Lanka
Video outgoing-inspection	Provided
Machinery Test Report	Provided
Marketing Type	New Product 2021
Place of Origin	China
Brand Name	Atlas Copco - Pneumatech Oaliss

Types of compressed air dryers
Refrigeration dryers
Refrigeration dryers are used for PDPs between +3°C/37.4°F to +10°C/50°F with the freezing point of water (0°C/ 32°F) as the lower limit.
By cooling the compressed air with a closed refrigerationsystem a large amount of water condenses and can beseparated. Afterwards the compressed air is reheatedwith the incoming air to around room temperature. In thisway the moisture content of the air stays well below themaximum moisture holding capacity at normal (nonfreezing) ambient temperatures, meaning that the relative humidity stays below 100%. It is recommended to stay below 50% relative humidity to avoid any condensation to happen on local cold spots of the piping network.

Adsorption dryers
Adsorption dryers are used when PDPs from -10°C/14°F down to -70°C/-94°F are to be achieved.

They make use of a material which has a high affinityto attract moisture, so called hygroscopic materialor desiccant. The adsorption of moisture causes thedesiccant to be gradually saturated with water.Therefore, the desiccant needs to be regeneratedregularly to regain its drying capacity. Adsorption dryersare typically built with two drying vessels ("towers")for that purpose: the first tower will dry the incomingcompressed air while the second one is beingregenerated. To ensure continuity, each vessel switchestasks when the other one is completely regenerated.

Oaliss's objective is to be "Your very own system provider". To fulfill this objective, Oaliss pays great attention to customer's real needs and concerns, then provides feasible solutions. Oaliss chooses the most reliable suppliers from the industry and tests its performance before installing on our equipment. Product quality is our paramount goal. In the meantime, we do our best to fill the gaps between price and energy efficiency. Our equipment will be reliable enough to use and the price low enough to purchase. Combined with these distinct features, our high quality and variable products have been accepted by customers from various industries. Oaliss-your very own system provider.
Oaliss-your very own system provider.

Industrial equipment, printing service, pipelines, power plants, oil&gas, oil refinery, coating, painting,plastics, steel industry, rubber, mechanical, blow molding, color sorter machine, shipyard, sandblasting, metallurgy, etc.
To provide the right equipment to you, please send us your detailed requirements.

1 Q: How about the quality of products?
A: We are an authorized distributor of Atlas Copco. The quality and service could be assured.
2 Q: How long is your delivery lead time?
A: If there is stock, the lead time is about 3 working days after we get the payment if need to be produced, it depends.
3 Q: How about your overseas after-sale service?
A: (1)Provide customers with installation and commissioning online instructions. (2)Worldwide agents and after service available.
4 Q: Can you accept OEM&ODM orders?
A: Yes, we have a professional design team, OEM&ODM orders are highly welcomed.

Products

Ad

Basic Info.

Product Description